Home / Guides / EU Machinery Regulation

Manufacturer obligations under Machinery Regulation 2023/1230 (Article 10)

Article 10 is the manufacturer's to-do list under Regulation (EU) 2023/1230: what must be done before the first unit ships, what goes on every unit and what you must keep doing for years afterwards. This guide takes it paragraph by paragraph, shows who counts as a manufacturer and what changed from the Machinery Directive.

Written by Proxom Engineering Ltd, a UK mechanical design engineering company. Checked on 20 November 2026 against the text of Regulation (EU) 2023/1230 on EUR-Lex (OJ text and consolidated version of 27 July 2026; Article 10 is the same in both) and Directive 2006/42/EC. The pending Omnibus IV amending proposal (2025/0134(COD)) was not adopted on that date; this guide follows the text in force. General information, not legal advice.

The short answer

  1. Article 10 of Regulation (EU) 2023/1230 lists what the manufacturer of machinery or a related product must do. It applies to units placed on the market or put into service from 20 January 2027 (Article 54, as corrected by the corrigendum in OJ L 169, 4.7.2023).
  2. Before the first unit leaves: design and build to Annex III, draw up the Annex IV technical documentation, carry out the Article 25 conformity assessment, then sign the EU declaration of conformity and affix the CE marking (Article 10(1)-(2)).
  3. On every unit (or, where that is not possible, on the packaging or an accompanying document): model, series or type; year of construction; any batch or serial number; your name, registered trade name or registered trade mark, postal address and a website, e-mail address or other digital contact (Article 10(5)-(6)). With every unit: the instructions (paper, or digital with access marked on the product) and the EU declaration of conformity, or its internet address or machine-readable code given in the instructions (Article 10(7)-(8)).
  4. After it has shipped: keep the technical documentation and the declaration for at least 10 years (Article 10(3)), keep series production in conformity (Article 10(4)), take corrective action and inform the authorities where a product presents a risk (Article 10(9)), and answer reasoned requests from authorities (Article 10(10)).
  5. You may be a manufacturer without calling yourself one: a company that builds a machine for its own use (Article 3(18)(b)), an importer or distributor selling under its own name or modifying a product (Article 17), and anyone who carries out a substantial modification, except a non-professional user modifying their own machine for their own use (Article 18).
  6. An authorised representative can hold documents for you, but it cannot take over the design duty of Article 10(1) or drawing up the technical documentation (Article 12(1)).

Article 10 paragraph by paragraph

Paraphrased from the Official Journal text. The right-hand column is our engineering suggestion of what to have ready, not wording from the Regulation.

ArticleWhat it requiresWhat to have ready
10(1)When placing on the market or putting into service, the manufacturer ensures that the machinery or related product has been designed and constructed in accordance with the essential health and safety requirements of Annex III.Risk assessment and an Annex III applicability table: for each section, applies or not, why, and how it is met. See our Annex III list.
10(2)Before placing on the market or putting into service: draw up the technical documentation of Annex IV, Part A and carry out the relevant conformity assessment procedure of Article 25, or have it carried out. Where it demonstrates compliance with Annex III: draw up the EU declaration of conformity (Article 21) and affix the CE marking (Article 24).Technical file index, the chosen conformity route (module A if not in Annex I, Article 25(4); for Annex I, Part B, module A only with full application of harmonised standards or common specifications specific to that category and covering all relevant requirements, otherwise B + C, H or G; for Annex I, Part A, B + C, H or G, Article 25(2)-(3)), the signed declaration and the CE marking. Guides: Annex IV, Annex I routes, CE marking.
10(3)Keep the technical documentation and the EU declaration of conformity at the disposal of market surveillance authorities for at least 10 years after the product has been placed on the market or put into service. Where relevant, source code or programming logic in the technical documentation is made available to competent national authorities on a reasoned request, if they need it to check compliance with Annex III.A retention rule per machine or series (our suggestion for a series: count the 10 years from the last unit placed on the market or put into service), a storage location, and a decision on how you would give source code or control logic to an authority on request.
10(4)Procedures so that series production stays in conformity, taking account of changes in the production process, the design or characteristics, and changes in the harmonised standards, other technical specifications or common specifications declared against. Where appropriate given the risks: sample testing of products on the market and investigation of the results; if necessary, a register of complaints, of non-conforming products and of recalls, and keeping distributors informed.A change-control procedure that asks 'does this change affect the declaration or the technical file?', a trigger for new standards decisions, and, where your risks justify it, a complaints and recall register. See our harmonised standards guide.
10(5)The product bears at least the designation of the model, series or type, the year of construction (the year in which the manufacturing process was completed) and any batch or serial number or other identifying element that exists. Where size or nature does not allow this, the information goes on the packaging or in an accompanying document.Rating plate drawing with these fields plus the CE marking (Article 24) and the further markings of Annex III, section 1.7.3, and a rule for when the year of construction is set (the year manufacture is completed, not the year of sale).
10(6)The manufacturer's name, registered trade name or registered trade mark, the postal address, and a website, e-mail address or other digital contact, on the product or, where that is not possible, on the packaging or an accompanying document. The address gives a single point of contact, in a language easily understood by users and market surveillance authorities.Rating plate and label artwork updated with a digital contact. One contact point, not a list of branch offices.
10(7)Instructions for use and the information of Annex III accompany the product; they may be digital and must clearly describe the model they belong to. For digital instructions: show on the product (or packaging or accompanying document) how to access them; make them printable, downloadable and savable on an electronic device so the user can access them at all times, in particular during a breakdown, including where embedded in software; keep them accessible online for the expected lifetime and at least 10 years after placing on the market. A paper copy free of charge within one month if the user asks at the time of purchase. Paper safety information for machines intended for, or reasonably foreseeably used by, non-professional users. Language easily understood by users, as determined by the Member State concerned; clear, understandable and legible.An instructions plan per model: format, hosting and access marking, paper-on-request process and languages per target country. See our digital instructions guide.
10(8)The EU declaration of conformity (Annex V, Part A) accompanies the product, or the instructions and Annex III information give the internet address or machine-readable code where it can be accessed. A digital declaration stays accessible online for the expected lifetime and at least 10 years after placing on the market or putting into service.Decide: paper declaration in the box, or a web address or QR code in the instructions. See our declaration of conformity guide.
10(9)A manufacturer who considers or has reason to believe that a product it placed on the market or put into service does not conform takes the corrective action needed to bring it into conformity, withdraw it or recall it, as appropriate, immediately. Where the product presents a risk to the health or safety of persons (and, where appropriate, domestic animals, property or the environment), it immediately informs the competent national authorities of the Member States where it made the product available or put it into service, with details of the non-conformity and the corrective action.A short written procedure: who decides, how affected units are traced (serial numbers, customer list), and who informs which authority.
10(10)On a reasoned request from a competent national authority: provide all information and documentation, on paper or digitally, needed to demonstrate conformity, in a language easily understood by that authority; cooperate on actions to eliminate risks presented by products placed on the market or put into service.A named person and a target response time, and the technical file in a form you can send quickly.

Who counts as the manufacturer

The Article 10 duties fall on the manufacturer as defined in Article 3(18), and on others the Regulation treats as manufacturers.

WhoWhySource
Machine builder selling under its own nameManufactures, or has designed or manufactured, and markets under its name or trademark.Article 3(18)(a)
Company that subcontracts the buildHas the machine designed or manufactured by others and markets it under its own name: under Article 3(18)(a) it is the manufacturer of that machine, even though a subcontractor built it.Article 3(18)(a)
Factory building a machine for its own production lineManufactures the machine and puts it into service for its own use.Article 3(18)(b)
Importer or distributor selling under its own name, or modifying a product so compliance might be affectedTreated as the manufacturer and takes on the obligations of Articles 10 and 11.Article 17
Anyone carrying out a substantial modificationTreated as the manufacturer for that machine (or only for the affected machine in an assembly, as shown in the risk assessment). A non-professional user modifying their own machine for their own use is not.Article 18; see our Article 18 guide
Manufacturer of partly completed machineryHas its own, separate list of obligations.Article 11; see our partly completed machinery guide

What changed from the Machinery Directive

Under the correlation table in Annex XII, Article 5 of Directive 2006/42/EC corresponds to Articles 10 and 11 of the Regulation (Article 11 covers partly completed machinery). Most duties are familiar; the main differences:

TopicDirective 2006/42/ECRegulation (EU) 2023/1230
Who carries the dutiesArticle 5(1): 'the manufacturer or his authorised representative'Article 10 is addressed to the manufacturer. An authorised representative cannot be mandated with Article 10(1) or with drawing up the technical documentation (Article 12(1)).
Design to the essential requirementsArticle 5(1)(a), Annex IArticle 10(1), Annex III
Technical fileArticle 5(1)(b) and Annex VII, Part A: file available for at least 10 years from the date of manufacture (series: last unit produced)Article 10(2)-(3): Annex IV, Part A documentation, at least 10 years after placing on the market or putting into service; source code or programming logic on reasoned request where relevant
InstructionsArticle 5(1)(c): provide the necessary information, such as instructions; detail in Annex I, 1.7.4Article 10(7): digital instructions allowed under conditions, paper copy on request, paper safety information for non-professional users
DeclarationArticle 5(1)(e): draw up the EC declaration and ensure it accompanies the machineryArticle 10(8): paper declaration, or an internet address or machine-readable code in the instructions
Identification and contactAnnex I, section 1.7.3 (marking)Article 10(5)-(6): adds a website, e-mail address or other digital contact and a single contact point; the authorised representative is no longer part of the manufacturer's marking duty; packaging or an accompanying document allowed where marking the product is not possible
Series production, complaints, corrective action, authoritiesInternal measures for series manufacture were part of the technical file (Annex VII, Part A, 1(a)); sample testing, a complaints register, corrective action and informing authorities were not in Article 5Article 10(4), (9) and (10)

Worked example: an Article 10 record for one machine

Bag sealer BS-4 (fictional): Article 10 recordSeries machine, module A
01
Machine Fictional bag-sealing machine BS-4, built in series by a 12-person UK company, sold to EU food packers. Not in Annex I, so module A (Article 25(4)).
02
10(1)-(2) Risk assessment rev. C and Annex III table done; technical file index complete; declaration template filled; CE marking on the plate drawing BS-4-900.
03
10(3) Technical file and declaration archived per series; retention set to 10 years after the last BS-4 is placed on the market; PLC program archived per software version.
04
10(4) Engineering change form gains the question 'affects declaration or technical file?'; complaints log started in the service spreadsheet.
05
10(5)-(6) Plate: model BS-4, serial number, year of construction, company name, postal address, website and service e-mail; plus the CE marking and the Annex III 1.7.3 markings.
06
10(7)-(8) Instructions as PDF on the website with a QR code on the machine, printable and downloadable; paper copy on request at order; the instructions state the web address where the declaration can be accessed.
07
10(9)-(10) One-page procedure: the engineering manager decides on corrective action; the customer list by serial number is kept for recall; the technical file can be exported as one PDF.
Fictional example. It shows how to record each paragraph, not what your machine needs; base your own record on your risk assessment and route.

What to do before 20 January 2027

  1. Confirm who the manufacturer is for each machine, including machines built for your own use and machines you have built by a subcontractor.
  2. Finish the pre-market file: risk assessment, Annex III table, Annex IV technical file, conformity route, declaration, CE marking (Article 10(1)-(2)).
  3. Update the rating plate and markings: the Article 10(5)-(6) fields (designation, year of construction, serial number, name, postal address, digital contact), the CE marking (Article 24) and the further markings of Annex III, section 1.7.3 (visible, legible and indelible; chapter 2 to 6 and explosive-atmosphere markings; mass of parts handled with lifting equipment).
  4. Decide how instructions and the declaration travel: paper or digital, access marking, hosting for the lifetime and at least 10 years, paper on request (Article 10(7)-(8)).
  5. Set the 10-year retention for the technical file and declaration, and how source code or control logic would be shown to an authority (Article 10(3)).
  6. Add three short procedures: change control for series production, a complaints and recall register where your risks need it, and corrective action with informing authorities (Article 10(4) and (9)).
  7. Keep supply-chain records of the economic operators who supplied you and those you supplied (importers, distributors), so you can identify them to market surveillance authorities on request for at least 10 years after each supply (Article 19).
  8. Non-EU builder? Check who your EU-established economic operator is (Regulation (EU) 2019/1020) and what the importer must check; see our non-EU guide.

Questions

What are the obligations of a machinery manufacturer under Regulation 2023/1230?

Article 10 sets them out: design and build to Annex III; draw up the Annex IV technical documentation and carry out the Article 25 conformity assessment; sign the EU declaration of conformity and affix the CE marking; keep the documentation and declaration for at least 10 years; keep series production in conformity; mark model, year of construction, serial number and contact details; supply instructions and the declaration (paper or digital under conditions); take corrective action and inform authorities where a product presents a risk; and cooperate with authorities on request.

From when does Article 10 apply?

The Regulation applies from 20 January 2027 (Article 54, as corrected by the corrigendum in OJ L 169, 4.7.2023). Units placed on the market or put into service from that date must meet it; units placed on the market in conformity with Directive 2006/42/EC before that date can still be made available on the market (Article 52(1)). See our transition guide.

If I build a machine for my own factory, am I a manufacturer?

Yes. Article 3(18)(b) defines a manufacturer as including anyone who manufactures a product within the scope and puts it into service for its own use. Putting into service is the first use in the Union for its intended purpose (Article 3(13)). The Article 10 obligations then apply to that machine.

Can my authorised representative take over the manufacturer's obligations?

Only some. The mandate cannot cover Article 10(1) (design and construction to Annex III) or drawing up the technical documentation (Article 12(1)). It must at least allow the representative to keep the documentation and declaration available for 10 years, provide documents on request and cooperate with authorities (Article 12(2)).

How long must a manufacturer keep the technical file?

At least 10 years after the machinery or related product has been placed on the market or put into service, together with the EU declaration of conformity (Article 10(3)). Our practical reading for a series: plan the 10 years from the last unit placed on the market.

Must the year of construction be on the machine?

Yes, as part of the identification in Article 10(5): the year in which the manufacturing process was completed. Where the size or nature of the product does not allow marking, the information goes on the packaging or in an accompanying document.

Is an e-mail address now required on the rating plate?

Article 10(6) asks for the postal address and a website, e-mail address or other digital contact, on the product or, where that is not possible, on the packaging or in an accompanying document. One of the digital options is enough.

Does the manufacturer have to hand over source code?

Not routinely. Article 10(3) says that where relevant, source code or programming logic included in the technical documentation is made available to competent national authorities on a reasoned request, if they need it to check compliance with Annex III.

Must a manufacturer keep a complaints register?

If necessary. Article 10(4) requires sample testing where appropriate with regard to the risks, and, if necessary, a register of complaints, of non-conforming products and of recalls, with distributors kept informed.

Related guides: Technical file under Annex IV · Conformity assessment (Annex I) · Declaration of conformity contents · CE marking (Articles 23-24) · Digital instructions · Importers and authorised representatives · Distributors (Article 15) · Substantial modification (Article 18) · Harmonised standards (Article 20) · Regulation vs Directive · Market surveillance and penalties · Scope and exclusions (Article 2). We sell to businesses only; see Terms. Always verify against the official text of Regulation (EU) 2023/1230 on EUR-Lex.