Written by Proxom Engineering Ltd, a UK mechanical design engineering company. Checked on 20 November 2026 against the text of Regulation (EU) 2023/1230 on EUR-Lex (OJ text and consolidated version of 27 July 2026), Commission Implementing Decision (EU) 2026/2015 and the European Commission's harmonised standards page for machinery (as read on 19 November 2026). The pending Omnibus IV amending proposal (2025/0134(COD)) was not adopted on that date; this guide follows the text in force. The standards list changes by Commission decision: check the Official Journal before you rely on any status in this guide. General information, not legal advice.
The short answer
- Under Article 20(1) of Regulation (EU) 2023/1230, a machine that conforms with harmonised standards whose references are published in the Official Journal (OJ) is presumed to meet the Annex III essential health and safety requirements covered by those standards. Nothing more: requirements the standard does not cover still need your own solution.
- Using standards is voluntary. You may meet Annex III another way, but the technical file must then describe the other technical specifications you used for each requirement (Annex IV, Part A, point (f)).
- Status on 19 November 2026 (European Commission's machinery standards page): no list of harmonised standards under the Regulation has been published yet. The Commission says a first list is being prepared, will feature the vast majority of standards now cited under the Directive and 'can be expected before the end of this year' (Commission page, as read on 19 November 2026).
- The Directive's list (Implementing Decision (EU) 2023/1586) is repealed with effect from 20 January 2027 by Implementing Decision (EU) 2026/2015, the day the Regulation applies. Directive citations do not carry over by themselves.
- Where no standards are cited, the Commission may adopt common specifications by implementing act (Article 20(3)); conforming to them also gives a presumption (Article 20(6)). The Commission's machinery standards page did not mention any when this guide was checked.
- The status matters most for Annex I, Part B machines: Article 25(3) allows self-assessment (module A) only for machines built to harmonised standards or common specifications specific to that category and covering all relevant requirements. In our reading this means references published in the OJ for the Regulation, and a general type-A standard such as EN ISO 12100 would not qualify. Without them, plan for a notified body (B + C, H or G), and confirm your route with a notified body or authority.
What Article 20 says
Article 20 is the Regulation's equivalent of Article 7 of the Directive (correlation table, Annex XII). Paraphrased paragraph by paragraph:
| Article | What it says | What it means for you |
|---|---|---|
| 20(1) | A product that conforms with harmonised standards, or parts of them, whose references have been published in the OJ is presumed to conform with the Annex III requirements covered by those standards or parts. | The presumption is per requirement and per standard part. List, for each Annex III requirement, which clause of which cited standard you rely on. |
| 20(2) | The Commission requests the European standardisation organisations to draft harmonised standards for the Annex III requirements (Article 10(1) of Regulation (EU) No 1025/2012). | Standards are drafted by the European standardisation organisations (in practice CEN and CENELEC for machinery); only the Commission's publication of the reference in the OJ makes them 'harmonised' for the presumption. |
| 20(3) | The Commission may adopt implementing acts establishing common specifications, but only if conditions are met: among them, it requested a harmonised standard and the request was not accepted, the standards were not delivered on time, or they do not comply with the request; further conditions follow in the same paragraph. | Common specifications are a fallback, not a parallel route the Commission uses by default. |
| 20(4)-(5) | Before drafting, the Commission informs the committee under Article 22 of Regulation (EU) No 1025/2012, takes into account the views of relevant bodies or the expert group and consults stakeholders. | Common specifications take time; do not plan a 2027 shipment around one that does not exist yet. |
| 20(6) | A product that conforms with common specifications, or parts of them, is presumed to conform with the Annex III requirements they cover. | Same effect as a cited harmonised standard, for the requirements covered. |
| 20(7) | When the reference of a harmonised standard is published in the OJ, the Commission repeals the common specifications, or parts of them, covering the same requirements. | Watch both lists: a common specification can be replaced by a standard. |
| 20(8) | A Member State that considers a common specification does not entirely satisfy Annex III informs the Commission, which may amend it. | A presumption can be challenged; for harmonised standards the formal objection procedure is in Article 11 of Regulation (EU) No 1025/2012. |
Where the list stands
As read on 19 November 2026, the Commission's machinery standards page lists only the Directive's Implementing Decision (EU) 2023/1586 and its amendments, the latest of 4 September 2026 (Implementing Decision (EU) 2026/2015). It states that the date 20.01.2027 may be shown as the end of legal effect under the Directive, that a new implementing decision with the list under the Regulation is being prepared, that it will feature the vast majority of the standards now cited under the Directive, that standards which do not yet fully address new or updated requirements of the Regulation will be clarified to that extent, and that the first list can be expected before the end of the year.
Implementing Decision (EU) 2026/2015 itself repeals Implementing Decision (EU) 2023/1586 with effect from 20 January 2027 (Article 2). A presumption runs from the date a reference is published in the Official Journal.
| Topic | Until 19 January 2027 | From 20 January 2027 |
|---|---|---|
| Legal act | Directive 2006/42/EC | Regulation (EU) 2023/1230 (Article 54) |
| Where the presumption comes from | Article 7 of the Directive and the references in Implementing Decision (EU) 2023/1586, as amended | In normal circumstances Article 20(1) and (6) of the Regulation: references the Commission publishes in the OJ for the Regulation, and common specifications. (A separate presumption for machinery designated as crisis-relevant goods exists in the emergency rules added by Regulation (EU) 2024/2748, Article 25d.) |
| The Directive's list | In force | Implementing Decision (EU) 2023/1586 repealed (Implementing Decision (EU) 2026/2015, Article 2). The Commission notes that 20.01.2027 may be stated as the end of legal effect under the Directive. |
| The Regulation's list | Not yet published (status on 19 November 2026) | Expected by the Commission 'before the end of this year' (as read on 19 November 2026); check the OJ and the Commission page before you sign each declaration |
| Units already placed on the market under the Directive | Directive declaration and CE marking | Member States may not impede making them available on the market (Article 52(1)); the Regulation applies to units placed on the market or put into service from 20 January 2027. See our Article 52 guide. |
Which machines the status matters for
For most machines a missing list changes the wording of the paperwork, not the route. For Annex I, Part B machines it can change the route.
| Machine and route | Role of harmonised standards | If no Regulation list is published in time |
|---|---|---|
| Not listed in Annex I (most machines): module A, internal production control (Article 25(4)) | Voluntary. A cited standard gives a presumption for the requirements it covers; without one you show conformity with Annex III directly. | Module A stays available. Keep applying the current standards as the state of the art, record which clauses you used for each requirement, and state in the technical file that conformity is shown against Annex III directly (Annex IV, Part A, point (f)) until references are published under the Regulation. |
| Annex I, Part B (Article 25(3)) | Decides the route: module A only if the machine is designed and built to harmonised standards or common specifications specific to that category and covering all relevant requirements (Article 25(3)); in our reading, references published in the OJ for the Regulation. | In our reading, without such a reference module A is not open: plan EU type-examination + conformity to type (B + C), full quality assurance (H) or unit verification (G) with a notified body. Book early; see our Annex I guide. |
| Annex I, Part A (Article 25(2)) | A notified body is needed in any case (B + C, H or G). Standards help it: under module G, for example, the body carries out the tests set out in the relevant harmonised standards or common specifications, or equivalent tests (Annex X, point 4). | No change of route. Agree with your notified body which standards and editions it will assess against. |
| Partly completed machinery (Article 11) | The declaration of incorporation lists the harmonised standards or common specifications applied, with the date of the standard (Annex V, Part B, item 6). | Same as module A: name the standards you used and the parts applied (Annex IV, Part B, point (e)); where you used other specifications, describe them in the documentation. |
Where standards appear in your paperwork
| Document | What to write | Source |
|---|---|---|
| Technical file (Annex IV, Part A) | The references of the harmonised standards or common specifications applied; where applied only in part, which parts. Where they were not applied or only partly, a description of the other technical specifications used to meet each applicable requirement. | Annex IV, Part A, points (e) and (f) |
| EU declaration of conformity (Annex V, Part A) | References to the harmonised standards or common specifications applied, including the date of publication of the reference in the OJ (or the date of the common specification); or references to the other technical specifications, with their date. Where applied in part, which parts. | Annex V, Part A, item 7 |
| EU declaration of incorporation (Annex V, Part B) | References to the harmonised standards or common specifications applied, including the date of the standard or of the common specification, or to other technical specifications with their date. | Annex V, Part B, item 6 |
| Series production procedures | Procedures that keep series production in conformity, taking account of changes in the harmonised standards, other technical specifications or common specifications by reference to which conformity is declared. | Article 10(4) |
Worked example: one line of a standards register
What to do before 20 January 2027
- Make a standards register: every standard you use, edition and date, the clauses you rely on and the Annex III requirement each clause covers.
- Mark the status of each reference: cited under the Directive only, cited under the Regulation (with the OJ date), or not cited.
- Fill the gaps: for each Annex III requirement not covered by a cited standard, describe the solution and the other technical specifications you used (Annex IV, Part A, point (f)). Pay attention to the requirements that are new or extended in the Regulation, such as 1.1.9 (protection against corruption) and 1.2.1 (safety and reliability of control systems).
- Check your conformity route: if the machine is in Annex I, Part B and no category-specific standard or common specification is cited under the Regulation, we recommend booking a notified body now and confirming the route with it.
- Prepare two versions of declaration item 7: one for a reference published under the Regulation (with the OJ publication date) and one for 'other technical specifications' with their date.
- Re-check before you sign: read the Commission's machinery standards page and the OJ on the day you sign each declaration, and file a dated note of what you saw.
- Watch for restrictions: the Commission says standards that do not fully address new or updated requirements will be 'clarified to that extent', so a cited reference may give a presumption for part of a requirement only.
- Keep it current: put 'new OJ decision for machinery' into your series production change procedure (Article 10(4)).
Questions
Are there harmonised standards under the Machinery Regulation 2023/1230 yet?
Not on 19 November 2026. The European Commission's machinery standards page lists only decisions under Directive 2006/42/EC and says a first list under the Regulation is being prepared and 'can be expected before the end of this year'. Check the page and the Official Journal again before you sign a declaration.
Do standards cited under the Machinery Directive still give a presumption from 20 January 2027?
No. Directive 2006/42/EC is repealed from 20 January 2027, and Implementing Decision (EU) 2026/2015 repeals the Directive's list (Implementing Decision (EU) 2023/1586) from the same date, so from then on a presumption under Article 20(1) depends on references the Commission publishes in the Official Journal for the Regulation. The Commission expects most of the same standards to be cited under the Regulation, so the content of your work is rarely lost, but the declaration must refer to what is actually cited on the day.
Can I still CE mark a machine if no list is published by 20 January 2027?
Yes. The route is unchanged for machines not listed in Annex I (module A) and for Annex I, Part A machines (a notified body is needed in any case). For machines not in Annex I, harmonised standards are voluntary: you show conformity with Annex III directly, describe the specifications you used in the technical file (Annex IV, Part A, point (f)) and list them in the declaration as other technical specifications with their date (Annex V, Part A, item 7). For Annex I, Part B machines, module A depends on category-specific standards or common specifications (Article 25(3)); without them use B + C, H or G.
What are common specifications?
Technical requirements adopted by the Commission by implementing act that provide a means to comply with Annex III (Article 20(3)). The Commission may adopt them only under set conditions, for example when a requested harmonised standard has not been delivered or does not comply with the request. Conforming to them gives a presumption for the requirements they cover (Article 20(6)); they are repealed where a cited harmonised standard covers the same requirements (Article 20(7)).
Does a harmonised standard cover all of Annex III?
No. The presumption covers only the requirements the standard, or the part of it you applied, covers (Article 20(1)). Check which requirements the standard is meant to cover and any restriction published with its reference; the Commission says standards that do not fully address new or updated requirements of the Regulation will be clarified to that extent. Every remaining requirement needs your own documented solution.
Which date goes into the declaration of conformity?
For a harmonised standard: the date of publication of its reference in the Official Journal; for a common specification: its date; for other technical specifications: their date (Annex V, Part A, item 7). The declaration of incorporation asks for the date of the standard or common specification (Annex V, Part B, item 6). See our declaration of conformity guide.
Do I have to buy the standards?
Standards are sold by the national standards bodies; the Regulation does not make them free. You need the editions you actually apply, because the technical file and the declaration refer to them by reference and date.
What happens if a cited standard turns out to be wrong?
Market surveillance can attribute a non-compliance to shortcomings in a harmonised standard or a common specification (Article 43(5), points (b) and (c)); where the national measure is considered justified, the Commission applies Article 11 of Regulation (EU) No 1025/2012 for standards or Article 20(8) for common specifications (Article 44). Your series production procedure must take account of changes in the standards you declared against (Article 10(4)).
Related guides: Annex III requirements list · Conformity assessment (Annex I) · Declaration of conformity contents · Technical file under Annex IV · Transition (Article 52) · Protection against corruption (1.1.9) · CE marking (Articles 23-24) · Regulation vs Directive · US and non-EU builders. We sell to businesses only; see Terms. Always verify against the official text of Regulation (EU) 2023/1230 on EUR-Lex and the current list in the Official Journal.