Written by Proxom Engineering Ltd, a UK mechanical design engineering company. Checked on 15 November 2026 against the consolidated text of Regulation (EU) 2023/1230 on EUR-Lex (version of 27 July 2026) and Directive 2006/42/EC. The pending Omnibus IV amending proposal (2025/0134(COD)) was not adopted on that date; this guide follows the text in force. Headings are quoted; requirement texts are summarised. General information, not legal advice.
The short answer
- Annex III of Regulation (EU) 2023/1230 holds the essential health and safety requirements (EHSRs). It replaces Annex I of Directive 2006/42/EC for machines placed on the market or put into service from 20 January 2027, and it keeps the Directive's six-chapter structure and most section numbers (correlation table, Annex XII).
- It has a Part A with definitions (moved from section 1.1.1 of the Directive), a Part B with the General Principles (the risk assessment), and six chapters: 1 for all machinery, 2 to 6 supplementary for certain categories and risks.
- Chapter 1 applies to every machine; chapters 2 to 6 apply where your machine falls into that category or presents that risk, according to the risk assessment (General Principles, point 4).
- A requirement applies only when the corresponding hazard exists under the conditions foreseen by the manufacturer or in foreseeable abnormal situations. Sections 1.1.2 (safety integration), 1.7.3 (marking) and 1.7.4 (instructions) apply in all cases (General Principles, point 2).
- The main additions compared with the Directive: 1.1.9 protection against corruption, an extended 1.2.1 (control systems, including reasonably foreseeable malicious attempts and logs of safety software), self-evolving behaviour (General Principles and 1.1.6), and autonomous mobile machinery with a supervisory function in chapter 3.
- Your technical file must list the EHSRs that apply and the protective measures used for each (Annex IV, Part A, point (b)). The full list below is the starting point for that applicability table.
How Annex III decides what applies
General Principles, point 1: the manufacturer ensures a risk assessment is carried out to determine the EHSRs that apply, then designs and builds the machine to eliminate hazards or, if that is not possible, minimise all relevant risks. In an iterative process the manufacturer (a) determines the limits of the machine, including intended use and reasonably foreseeable misuse, (b) identifies the hazards and hazardous situations, (c) estimates the risks, (d) evaluates them and (e) eliminates the hazards or reduces the risks with protective measures in the order of section 1.1.2(b): inherently safe design, then protective measures, then information on residual risks.
Point 2: the obligations apply only when the corresponding hazard exists under the conditions foreseen by the manufacturer or in foreseeable abnormal situations; 1.1.2, 1.7.3 and 1.7.4 apply in all cases. Point 3: the EHSRs are mandatory; where the state of the art does not allow their objectives to be met, the machine must approach them as far as possible. Point 4: chapter 1 and one or more of the other chapters are taken into account according to the risk assessment; environmental requirements apply only to the machinery in section 2.4. Point 5: the same principles apply to partly completed machinery. Our risk assessment guide goes through the steps with a worked example.
Which chapters apply to your machine
| Chapter | Title | Applies to | Main topics |
|---|---|---|---|
| Part B | General Principles | Every manufacturer, including of partly completed machinery (point 5) | The risk assessment and risk reduction process, steps (a) to (e), and the rules on which requirements apply |
| 1 | Essential health and safety requirements | All machinery and related products | Safety integration, materials, lighting, handling, ergonomics, operating positions, seating, protection against corruption, control systems, mechanical risks, guards and protective devices, other risks, maintenance, information |
| 2 | Supplementary: certain categories | Machinery for foodstuffs, cosmetics or pharmaceutical products (2.1); portable hand-held or hand-guided machinery, including portable fixing and other impact machinery (2.2); machinery for working wood and materials with similar physical characteristics (2.3); machinery for applying plant protection products (2.4) | Hygiene and cleaning, hand-held machine controls and vibration declaration, woodworking-specific risks, environmental protection (only 2.4 has environmental requirements) |
| 3 | Supplementary: mobility | Machinery presenting risks due to its mobility, including autonomous mobile machinery | Driving and work positions, supervisory function, travelling controls, roll-over and tip-over, falling objects, batteries, overhead power lines, marking and instructions |
| 4 | Supplementary: lifting operations | Machinery presenting risks due to lifting operations, and lifting accessories, chains, ropes and webbing | Stability, rails, mechanical strength and working coefficients, pulleys, drums, ropes and chains, loading control, markings, instructions |
| 5 | Supplementary: underground work | Machinery intended for underground work | Stability, movement, control devices, stopping, fire, exhaust emissions |
| 6 | Supplementary: lifting of persons | Machinery presenting particular risks due to the lifting of persons | Strength (working coefficients generally doubled), loading control, controls, risks to persons in or on the carrier, fixed landings, markings |
The full list of Annex III sections
180 numbered headings, as they appear in the English text on EUR-Lex. Tags mark the main sections that are new or extended compared with Annex I of Directive 2006/42/EC; other sections also have wording changes, so compare the full texts. Open each chapter to see its sections.
Chapter 1. Essential health and safety requirements (73 headings)
- 1.1 General remarks
- 1.1.1 Applicability
- 1.1.2 Principles of safety integration
- 1.1.3 Materials and products
- 1.1.4 Lighting
- 1.1.5 Design of machinery or a related product to facilitate its handling
- 1.1.6 Ergonomics extended
- 1.1.7 Operating positions
- 1.1.8 Seating
- 1.1.9 Protection against corruption new section
- 1.2 Control systems
- 1.2.1 Safety and reliability of control systems extended
- 1.2.2 Control devices
- 1.2.3 Starting
- 1.2.4 Stopping
- 1.2.4.1 Normal stop
- 1.2.4.2 Operational stop
- 1.2.4.3 Emergency stop
- 1.2.4.4 Assembly of machinery or related products
- 1.2.5 Selection of control or operating modes
- 1.2.6 Failure of the power supply or communication network connection heading extended
- 1.3 Protection against mechanical risks
- 1.3.1 Risk of loss of stability
- 1.3.2 Risk of break-up during operation
- 1.3.3 Risks due to falling or ejected objects
- 1.3.4 Risks due to surfaces, edges or angles
- 1.3.5 Risks related to a combined machinery or related product
- 1.3.6 Risks related to variations in operating conditions
- 1.3.7 Risks related to moving parts extended
- 1.3.8 Choice of protection against risks arising from moving parts
- 1.3.8.1 Moving transmission parts
- 1.3.8.2 Moving parts involved in the process
- 1.3.9 Risks of uncontrolled movements
- 1.4 Required characteristics of guards and protective devices
- 1.4.1 General requirements
- 1.4.2 Special requirements for guards
- 1.4.2.1 Fixed guards
- 1.4.2.2 Interlocking movable guards
- 1.4.2.3 Adjustable guards restricting access
- 1.4.3 Special requirements for protective devices
- 1.5 Risks due to other causes
- 1.5.1 Electricity supply
- 1.5.2 Static electricity
- 1.5.3 Energy supply other than electricity
- 1.5.4 Errors of fitting
- 1.5.5 Extreme temperatures
- 1.5.6 Fire
- 1.5.7 Explosion
- 1.5.8 Noise
- 1.5.9 Vibrations
- 1.5.10 Radiation
- 1.5.11 External radiation
- 1.5.12 Laser radiation
- 1.5.13 Emissions of hazardous materials and substances
- 1.5.14 Risk of being trapped in a machine
- 1.5.15 Risk of slipping, tripping or falling
- 1.5.16 Lightning
- 1.6 Maintenance
- 1.6.1 Machinery or related product maintenance
- 1.6.2 Access to operating positions and servicing points
- 1.6.3 Isolation of energy sources
- 1.6.4 Operator intervention
- 1.6.5 Cleaning of internal parts
- 1.7 Information
- 1.7.1 Information and warnings on the machinery or related product
- 1.7.1.1 Information and information devices
- 1.7.1.2 Warning devices
- 1.7.2 Warning of residual risks
- 1.7.3 Marking of machinery or related products
- 1.7.4 Instructions for use
- 1.7.4.1 General principles for the drafting of instructions for use
- 1.7.4.2 Contents of the instructions for use
- 1.7.5 Sales literature
Chapter 2. Supplementary essential health and safety requirements for certain categories of machinery and related products (27 headings)
- 2.1 Machinery and related products for foodstuffs and machinery and related products for cosmetics or pharmaceutical products
- 2.1.1 General
- 2.1.2 Instructions for use
- 2.2 Portable hand-held or hand-guided machinery or related products
- 2.2.1 General
- 2.2.1.1 Instructions for use
- 2.2.2 Portable fixing and other impact machinery or related products
- 2.2.2.1 General
- 2.2.2.2 Instructions for use
- 2.3 Machinery or related products for working wood and material with similar physical characteristics
- 2.4 Machinery or related products for plant protection products application
- 2.4.1 (Definitions - untitled in Annex III)
- 2.4.2 General
- 2.4.3 Controls and monitoring
- 2.4.4 Filling and emptying
- 2.4.5 Application of plant protection products
- 2.4.5.1 Application rate
- 2.4.5.2 Distribution, deposition and drift of plant protection products
- 2.4.5.3 Tests
- 2.4.5.4 Losses during stoppage
- 2.4.6 Maintenance
- 2.4.6.1 Cleaning
- 2.4.6.2 Servicing
- 2.4.7 Inspections
- 2.4.8 Marking of nozzles, strainers and filters
- 2.4.9 Indication of the plant protection product in use
- 2.4.10 Instructions for use
Chapter 3. Supplementary essential health and safety requirements to offset risks due to the mobility of machinery or related products (33 headings)
- 3.1 General
- 3.1.1 (Definitions - untitled in Annex III)
- 3.2 Work positions
- 3.2.1 Driving position
- 3.2.2 Seating
- 3.2.3 Positions for other persons
- 3.2.4 Supervisory function new section
- 3.3 Control systems
- 3.3.1 Control devices
- 3.3.2 Starting/moving
- 3.3.3 Travelling function
- 3.3.4 Movement of pedestrian-controlled machinery
- 3.3.5 Control circuit failure
- 3.4 Protection against mechanical risks
- 3.4.1 Uncontrolled movements
- 3.4.2 Moving transmission parts
- 3.4.3 Roll-over and tip-over
- 3.4.4 Falling objects
- 3.4.5 Means of access
- 3.4.6 Towing devices
- 3.4.7 Transmission of power between self-propelled machinery (or a tractor) and recipient machinery
- 3.5 Protection against other risks
- 3.5.1 Batteries
- 3.5.2 Fire
- 3.5.3 Emissions of hazardous substances
- 3.5.4 Risk of contact with live overhead power lines
- 3.6 Information and indications
- 3.6.1 Signs, signals and warnings
- 3.6.2 Marking
- 3.6.3 Instructions for use
- 3.6.3.1 Vibrations
- 3.6.3.2 Multiple uses
- 3.6.3.3 Autonomous mobile machinery or related products new section
Chapter 4. Supplementary essential health and safety requirements to offset risks due to lifting operations (28 headings)
- 4.1 General
- 4.1.1 (Definitions - untitled in Annex III)
- 4.1.2 Protection against mechanical risks
- 4.1.2.1 Risks due to lack of stability
- 4.1.2.2 Machinery or related products running on guide rails and rail tracks
- 4.1.2.3 Mechanical strength
- 4.1.2.4 Pulleys, drums, wheels, ropes and chains
- 4.1.2.5 Lifting accessories and their components
- 4.1.2.6 Control of movements
- 4.1.2.7 Movements of loads during handling
- 4.1.2.8 Machinery serving fixed landings
- 4.1.2.8.1 Movements of the carrier
- 4.1.2.8.2 Access to the carrier
- 4.1.2.8.3 Risks due to contact with the moving carrier
- 4.1.2.8.4 Risk due to the load falling off the carrier
- 4.1.2.8.5 Landings
- 4.1.3 Fitness for purpose
- 4.2 Requirements for machinery or related products whose power source is other than manual effort
- 4.2.1 Control of movements
- 4.2.2 Loading control
- 4.2.3 Installations guided by ropes
- 4.3 Information and markings
- 4.3.1 Chains, ropes and webbing
- 4.3.2 Lifting accessories
- 4.3.3 Lifting machinery or related products
- 4.4 Instructions for use
- 4.4.1 Lifting accessories
- 4.4.2 Lifting machinery or related products
Chapter 5. Supplementary essential health and safety requirements for machinery or related products intended for underground work (6 headings)
- 5.1 Risks due to lack of stability
- 5.2 Movement
- 5.3 Control devices
- 5.4 Stopping
- 5.5 Fire
- 5.6 Exhaust emissions
Chapter 6. Supplementary essential health and safety requirements for machinery or related products presenting particular risks due to the lifting of persons (13 headings)
- 6.1 General
- 6.1.1 Mechanical strength
- 6.1.2 Loading control for machinery or related products moved by power other than human strength
- 6.2 Control devices
- 6.3 Risks to persons in or on the carrier
- 6.3.1 Risks due to movements of the carrier
- 6.3.2 Risk of persons falling from the carrier
- 6.3.3 Risk due to objects falling on the carrier
- 6.4 Machinery or related products serving fixed landings
- 6.4.1 Risks to persons in or on the carrier
- 6.4.2 Controls at landings
- 6.4.3 Access to the carrier
- 6.5 Markings
Sections 2.4.1, 3.1.1 and 4.1.1 contain definitions and have no heading in Annex III. Headings only: read the full requirement text on EUR-Lex before you mark a section applicable or not applicable.
What is new compared with Annex I of the Directive
| Topic | Directive 2006/42/EC, Annex I | Regulation 2023/1230, Annex III |
|---|---|---|
| Structure | Annex I: General Principles, then 1.1.1 with definitions | Annex III: Part A definitions, Part B General Principles, chapters 1 to 6 with the same numbering logic (Annex XII) |
| Risk assessment (Part B, point 1) | Determine limits, identify hazards, estimate, evaluate and reduce risks | Same iterative process, now also covering risks from interactions between machines that form an assembly, and hazards from intended fully or partially self-evolving behaviour or logic |
| 1.1.6 Ergonomics | Stress reduced to the minimum possible, taking into account ergonomic principles such as five listed ones, the last being adapting the man-machine interface to the foreseeable characteristics of the operators | Stress to be eliminated or reduced to the minimum, taking into account at least seven principles: new point (b) (demanding postures, movements and manual force beyond the operator's capacity); point (f) extends the interface rule to machines with self-evolving behaviour or logic designed to operate with varying levels of autonomy; new point (g): where relevant such machines respond to people adequately and communicate their planned actions in a comprehensible manner |
| 1.1.9 Protection against corruption | No such section | New: connecting another device, directly or through a remote device, must not lead to a hazardous situation; hardware, software and data critical for compliance protected against accidental or intentional corruption; the machine identifies its safety-relevant software and collects evidence of legitimate or illegitimate interventions |
| 1.2.1 Control systems | Withstand operating stresses and external influences; faults must not lead to hazardous situations | Also reasonably foreseeable malicious attempts by third parties; a tracing log of intervention data and of safety software versions uploaded after placing on the market, enabled for five years after each upload and used only to demonstrate conformity on a reasoned request from a competent national authority; hazardous changes of settings or rules during a learning phase are prevented; self-evolving systems stay within their defined task and movement space and keep safety-related decision data for one year after collection |
| 1.3.7 Moving parts | Moving parts designed to prevent risks of contact that could lead to accidents | Prevention of risks of contact, and of psychological stress, adapted also to human-machine coexistence in a shared space without direct collaboration and to human-machine interaction |
| 1.2.6 | Failure of the power supply | Failure of the power supply or communication network connection |
| Chapter 3 | Mobile machinery with a driver or remote control | Adds autonomous mobile machinery: a supervisory function (3.2.4), an enclosed zone with a peripheral protection system or devices that detect persons, domestic animals and other obstacles, as the risk assessment requires, and instructions for autonomous mobile machinery (3.6.3.3) |
| Presumption of conformity | Harmonised standards cited in the OJ under the Directive | Harmonised standards or common specifications under the Regulation (Article 20); certification under an EU cybersecurity scheme (Regulation (EU) 2019/881) referenced in the OJ for 1.1.9 and 1.2.1, insofar as it covers them |
Summary of the main changes, not a complete comparison. For the software and cybersecurity sections see our 1.1.9 guide; for every other change between the two laws see Regulation vs Directive.
Worked example: part of an applicability table
Annex IV, Part A, point (b) asks for the risk assessment documentation with (i) a list of the EHSRs that apply and (ii) the protective measures implemented for each, with residual risks where appropriate. Here is an extract for a fictional carton erector (fixed machine, safety PLC, interlocked side doors, light curtain at the magazine, hot-melt glue):
| Annex III section | Applies? | Reason | Measure or standard |
|---|---|---|---|
| 1.1.2 Principles of safety integration | Applies (always) | General Principles, point 2 | Measures chosen in the order inherent design, safeguarding, information; recorded per hazard in the risk assessment |
| 1.1.6 Ergonomics | Applies | Operator loads flat carton blanks into the magazine 40 times a shift | Magazine loading height 900 to 1100 mm; no machine-paced loading |
| 1.1.9 Protection against corruption | Applies | Safety PLC program and light-curtain configuration can be changed on site with a laptop | Password-protected safety configuration, sealed programming port, safety program checksum shown on the HMI and filed |
| 1.2.1 Safety and reliability of control systems | Applies | Guard interlocks and light curtain act through the safety PLC | Safety functions designed and validated to the required performance level (EN ISO 13849-1); intervention log enabled |
| 1.2.4.3 Emergency stop | Applies | Operator and maintenance positions on both sides | Two emergency stop devices, stop category chosen in the risk assessment |
| 1.3.7 / 1.4.2.2 Moving parts and interlocking guards | Applies | Folding arms and glue head behind the side doors | Interlocked doors with guard locking; machine stops before access |
| 1.5.7 Explosion | Not applicable | No explosive atmosphere, gases, dusts or explosive materials; hot-melt glue below its flash point in use | Reason recorded; re-check if the glue or location changes |
| 1.6.3 Isolation of energy sources | Applies | Electrical supply and compressed air | Lockable main switch and lockable pneumatic dump valve |
| 1.7.3 Marking and 1.7.4 Instructions | Applies (always) | General Principles, point 2 | Rating plate per Article 10 and 1.7.3; instructions per 1.7.4.2 including residual risks |
| 2.1 Foodstuffs, cosmetics, pharmaceutical | Not applicable | Erects empty cartons; no contact with foodstuffs, cosmetics or pharmaceutical products | Reason recorded |
| Chapters 3 to 6 | Not applicable | Fixed machine, no lifting operations, not for underground work, no lifting of persons | Reason recorded per chapter |
Fictional and incomplete. A real table covers every section of chapter 1 and every chapter 2 to 6 that could apply, and it is updated each time the design changes.
Questions
How many essential health and safety requirements does Annex III have?
It depends how you count. The list on this page has 180 numbered headings (sections and sub-sections) across six chapters, 73 of them in chapter 1. Many sections contain several separate requirements, so count the requirements in each applicable section when you write your applicability table, not just the headings.
Do I have to address every section of Annex III?
You have to examine all of it: General Principles, point 4 says chapter 1 and one or more of the other chapters are taken into account depending on the results of the risk assessment. A requirement applies only where the corresponding hazard exists (point 2), but sections 1.1.2, 1.7.3 and 1.7.4 always apply. Annex IV only requires the list of applicable requirements, but a short reason for each not-applicable section makes the file much easier to defend to a notified body or market surveillance authority.
Is Annex III just Annex I of the Directive renumbered?
Mostly the same chapters and section numbers, so a Directive-era applicability table is a good starting point (the correlation table in Annex XII maps Directive Annex I to Regulation Annex III). But the content is not identical: definitions moved to Part A, the General Principles were extended, 1.1.9 is new, 1.2.1, 1.1.6 and chapter 3 were extended, (and, outside Annex III, the declaration must now refer to the Regulation). Re-check every row rather than copying it.
Where do harmonised standards fit in?
Following a harmonised standard cited in the Official Journal under the Regulation gives a presumption of conformity with the requirements it covers (Article 20). As at 15 November 2026 no harmonised standards had been cited in the Official Journal under Regulation (EU) 2023/1230. Standards still describe the state of the art, so name the standard you used for each requirement in your table, but the presumption only arises once the reference is published under the Regulation. Citations under the Directive (Implementing Decision (EU) 2023/1586) end on 20 January 2027 (Implementing Decision (EU) 2026/2015).
What changes for partly completed machinery?
The General Principles apply to its risk assessment too (point 5). The relevant requirements do not include those that can only be fulfilled when the partly completed machinery is incorporated, but 1.1.2 applies in all cases (1.1.1). The declaration of incorporation states which Annex III requirements are applied and fulfilled. See our partly completed machinery guide.
Does my machine need a cybersecurity certificate for 1.1.9?
No. Certification or a statement of conformity under an EU cybersecurity scheme referenced in the Official Journal is one way to obtain a presumption of conformity for 1.1.9 and 1.2.1, insofar as it covers those requirements (Article 20). Without it you show conformity in the risk assessment and technical file. See our protection against corruption guide.
When does Annex III start to apply?
To each machine or related product placed on the market or put into service from 20 January 2027 (Article 54). Until then the Directive's Annex I applies; see our transition guide.
Related guides: Risk assessment (Annex III) · Protection against corruption (1.1.9) · Technical file under Annex IV · Regulation vs Directive · Harmonised standards (Article 20) · Conformity assessment (Annex I) · Declaration of conformity contents · CE marking (Articles 23-24) · Partly completed machinery. We sell to businesses only; see Terms. Always verify against the official text of Regulation (EU) 2023/1230 on EUR-Lex.